Patchbay & crackle check Route your sound · find what crackles · fixes for your system
Pedalboard Drives hit the amp; modulation and delay come after the cab
Amp
Cabinet & room
Tuner
–
Amp off
Recorder Blank project · free · stays on this device
How this fixes a budget interface
Voice processing off. Echo cancellation, noise suppression and auto-gain are disabled, so notes don't pump, swirl or get chopped.
Guitar in one ear? Many USB guitar interfaces send the guitar on the left channel only. Pick the channel, or let Auto-set find it, and it plays in both ears.
Pickup restore. Low-impedance inputs load passive pickups and dull the top end. This puts the pickup's resonant peak and air back, like a proper Hi-Z input.
Hum filter and gate. Notches out USB ground-loop hum and its harmonics; the gate silences hiss between phrases without cutting sustain.
Real amp behaviour. Two oversampled tube-style preamp stages, a tone stack, power-amp saturation with sag, a speaker cabinet and a room.
Lowest latency. Runs at the interface's own sample rate with the smallest buffer the browser allows. Chrome or Edge on a computer is usually fastest.
Download it. Press Install app (Chrome, Edge, Android) or use Share → Add to Home Screen (iPhone, iPad). It opens like an app and works offline: the amp runs entirely on your device.
On a phone? Plug the interface into the phone (USB-C, or Lightning with Apple's camera adapter), open this page in Safari or Chrome, and use headphones on the interface. The screen stays on while the amp is on; if the sound stops after a call or another app, tap the page. Add it to your home screen to use it like an app.
Budget laptop or Chromebook? Processing on Auto switches to Light on 4-core or 4 GB machines (for example an Acer Aspire 3 or Chromebook 315), so it plays without crackles. On a Chromebook, pick the interface under Settings → Device → Audio, or in the Input list here.
No interface? A guitar can plug straight into a laptop's, Chromebook's or phone's headset jack with a cheap passive adapter (6.35 mm guitar jack to 3.5 mm TRRS headset plug, often sold as a "guitar to smartphone" cable). On a USB-C phone, add a USB-C headphone adapter that supports a microphone. Press set up for direct plug-in under Interface, turn the guitar's volume to about half (that input is very sensitive), choose the headset or external mic as Input, then Auto-set input. Expect a little more hiss and delay than a USB interface. Listen on wired headphones (many of these adapters have their own headphone socket); Bluetooth adds too much delay to play along.
Patchbay. Plug virtual cables from the Amp or the Dry guitar into Headphones, the Recorder or a second output device, each with its own level. Record the dry guitar to re-amp it later, or send the amp to a stream or speakers while you play on headphones.
Crackle check. It tells a hardware fault (clicks on the input while the guitar is silent: a worn cable, loose jack or failing interface) apart from the computer dropping audio, and shows the fixes for the system it detects (ChromeOS, Linux, Windows, macOS, Android, iPhone). On Linux it offers a PipeWire + patchbay setup script.
Crackles or pops? Set Buffer to Stable first; it trades a few milliseconds of delay for a steady stream. Then try Processing on Light, plug the interface straight into the computer (no hub), use wired headphones (not Bluetooth), close other tabs and apps using audio, and on a laptop plug in the charger. On Windows, turn off Audio enhancements for the interface and set it and your headphones to the same rate (48000 Hz) under Sound → device → Properties.
Interface has its own cab sim? Set the cabinet to Off so it isn't applied twice, or load your favourite IR.
Record your own tracks, free. The recorder is a blank project: press Record, play, and each take becomes a track. Record again to layer rhythm, lead and bass parts with a click and count-in. It records what you hear from the amp, lines takes up for your interface's delay, and exports each track or the mix as 24-bit WAV. Takes are saved in this browser, so a reload doesn't lose them.
Singing or acoustic? Set Signal to Mic → vocal. The mic is recorded clean through a light preamp (low cut and gentle tube warmth), skipping the amp, pedals and cabinet.
Mix like a console. Every track has an FX rack (compressor, EQ, saturation, delay, chorus, limiter, plate reverb) before its fader, and the master bus has its own rack. Load the Vocal, Guitar polish or Master chain as a starting point. Effects never change the recorded take, so you can always undo them.
Private. Your guitar never leaves the device: nothing is uploaded. Takes you record and your settings stay in this browser until you export or delete them.